References

Cabibbo, M., 2012. Partial dissolution of strengthening particles induced by equal channel angular pressing in an Al-Li-Cu alloy. Mater. Charact., 68: 7-13.
Direct Link  |  

Chen, B., D.L. Lin, L. Jin, X.Q. Zeng and C. Lu, 2008. Equal-channel angular pressing of magnesium alloy AZ91 and its effects on microstructure and mechanical properties. Mater. Sci. Eng. A., 483: 113-116.
Direct Link  |  

Estrin, Y. and A. Vinogradov, 2010. Fatigue behaviour of light alloys with ultrafine grain structure produced by severe plastic deformation: An overview. Int. J. Fatigue, 32: 898-907.
CrossRef  |  

Farshidi, M.H., M. Kazeminezhad and H. Miyamoto, 2013. On the natural aging behavior of Aluminum 6061 alloy after severe plastic deformation. Mater. Sci. Eng. A., 580: 202-208.
Direct Link  |  

Farshidi, M.H., M. Kazeminezhad and H. Miyamoto, 2013. Severe plastic deformation of 6061 aluminum alloy tube with pre and post heat treatments. Mater. Sci. Eng. A, 563: 60-67.
CrossRef  |  

Hamada, A.S., L.P. Karjalainen, P.V. Surya and R.D.K. Misra, 2011. Fatigue behavior of ultrafine-grained and coarse-grained Cr-Ni austenitic stainless steels. Mater. Sci. Eng. A., 528: 3890-3896.
Direct Link  |  

Jafarlou, D.M., E. Zalnezhad, M.A. Hassan, M.A. Ezazi and N.A. Mardi et al., 2016. Severe plastic deformation of tubular AA 6061 via equal channel angular pressing. Mater. Des., 90: 1124-1135.
Direct Link  |  

Jimenez, A.P., V.C. Gutierrez, M.H. Staia and P.E.S. Cabrera, 2007. Tensile and fatigue properties of 6063-T6 aluminium alloy coated with electroless Ni-P deposit. Mater. Sci. Technol., 23: 253-263.
Direct Link  |  

Kim, W.J., C.Y. Hyun and H.K. Kim, 2006. Fatigue strength of ultrafine-grained pure Ti after severe plastic deformation. Scr. Mater., 54: 1745-1750.
Direct Link  |  

Langdon, T.G., 2007. The principles of grain refinement in equal-channel angular pressing. Mater. Sci. Eng. A., 462: 3-11.
Direct Link  |  

Liu, M.P., T.H. Jiang, W.A.N.G. Jun, L.I.U. Qiang and Z.J. Wu et al., 2014. Aging behavior and mechanical properties of 6013 aluminum alloy processed by severe plastic deformation. Trans. Nonferrous Metals Soc. China, 24: 3858-3865.
Direct Link  |  

Mishra, S.K., A. Brahma and K. Dutta, 2016. Low cycle fatigue life prediction of Al-Si-Mg Alloy using artificial neural network approach. Trans. Indian Inst. Metals, 69: 597-602.
CrossRef  |  Direct Link  |  

Murashkin, M., I. Sabirov, D. Prosvirnin, I. Ovid'ko and V. Terentiev et al., 2015. Fatigue behavior of an ultrafine-grained Al-Mg-Si Alloy processed by high-pressure torsion. Metals, 5: 578-590.
CrossRef  |  Direct Link  |  

Pan, B., T.M. Jiang, J.M. Jin and M.D. Ma, 2012. Failure analysis of aircraft aluminum alloy structures in coastal environments. Adv. Mater. Res., 432: 1509-1513.

Placido, J.C.R., P.E.V.D. Miranda, A.T. Netto, I.P. Pasqualino and G.F. Miscow et al., 2005. Fatigue analysis of Aluminum drill pipes. Mater. Res., 8: 409-415.
Direct Link  |  

Serban, N., V.D. Cojocaru and M. Butu, 2012. Mechanical behavior and microstructural development of 6063-T1 aluminum alloy processed by equal-channel angular pressing (ECAP): Pass number influence. JOM., 64: 607-614.
CrossRef  |  Direct Link  |  

Shaeri, M.H., M. Shaeri, M.T. Salehi, S.H. Seyyedein and F. Djavanroodi, 2015. Microstructure and texture evolution of Al-7075 alloy processed by equal channel angular pressing. Trans. Nonferrous Metals Soc. China, 25: 1367-1375.
Direct Link  |  

Shaeri, M.H., M.T. Salehi, S.H. Seyyedein, M.R. Abutalebi and J.K. Park, 2013. Characterization of microstructure and deformation texture during equal channel Angular pressing of Al-Zn-Mg-Cu alloy. J. Alloys Compounds, 576: 350-357.
Direct Link  |  

Toth, L.S. and C. Gu, 2014. Ultrafine-grain metals by severe plastic deformation. Mater. Charact., 92: 1-14.
Direct Link  |  

Valiev, R.Z., Y. Estrin, Z. Horita, T.G. Langdon, M.J. Zehetbauer and Y.T. Zhu, 2006. Producing bulk ultrafine-grained materials by severe plastic deformation. JOM., 58: 33-39.
CrossRef  |  Direct Link  |  

Walton, D., S. Prayoonrat and S. Taylor, 1986. Computer-aided fatigue analysis. Comput. Aided Des., 18: 263-274.
Direct Link  |  

Wang, C., F. Li, B. Chen, Z. Yuan and H. Lu, 2012. Severe plastic deformation techniques for bulk ultrafine-grained materials. Rare Metal Mater. Eng., 41: 941-946.
Direct Link  |  

Zhao, T. and Y. Jiang, 2008. Fatigue of 7075-T651 Aluminum alloy. Intl. J. Fatigue, 30: 834-849.
Direct Link  |