References

Deris, A.M., A.M. Zain, R. Sallehuddin, S. Sharif and S. Yusuf, 2017. Grey Relational Analysis (GRA) of electrode wear rate in die sinking electric discharge machining. J. Eng. Appl. Sci., 12: 1795-1799.
CrossRef  |  Direct Link  |  

Dewangan, S., S. Gangopadhyay and C.K. Biswas, 2015. Study of surface integrity and dimensional accuracy in EDM using Fuzzy TOPSIS and sensitivity analysis. Meas., 63: 364-376.
Direct Link  |  

Fukuzawa, Y., N. Mohri, H. Gotoh and T.A.N.I. Takayuki, 2009. Three-dimensional machining of insulating ceramics materials with electrical discharge machining. Trans. Nonferrous Met. Soc. China, 19: 150-156.
CrossRef  |  Direct Link  |  

Han, F., J. Zhang and I. Soichiro, 2007. Corner error simulation of rough cutting in wire EDM. Precis. Eng., 31: 331-336.
Direct Link  |  

Khaja, M., R. Kumar and V. Singh, 2015. Modeling and optimization of WEDM process parameters on machining of AISI D2 steel using Response Surface Methodology (RSM). Intl. J. Adv. Res. Eng. Sci. Technol., 2: 49-53.

Marigoudar, R.N. and K. Sadashivappa, 2013. Effect of machining parameters on MRR and surface roughness in machining of ZA43/SiC_p composite by WEDM. Intl. J. Appl. Sci. Eng., 11: 317-330.
CrossRef  |  Direct Link  |  

Pandey, A. and S. Singh, 2010. Current research trends in variants of electrical discharge machining: A review. Intl. J. Eng. Sci. Technol., 2: 2172-2191.
Direct Link  |  

Patil, N.G. and P.K. Brahmankar, 2010. Determination of material removal rate in wire electro-discharge machining of metal matrix composites using dimensional analysis. Intl. J. Adv. Manuf. Technol., 51: 599-610.
CrossRef  |  Direct Link  |  

Patil, N.G. and P.K. Brahmankar, 2010. Some studies into wire electro-discharge machining of alumina particulate-reinforced aluminum matrix composites. Intl. J. Adv. Manuf. Technol., 48: 537-555.
CrossRef  |  Direct Link  |  

Puh, F., Z. Jurkovic, M. Perinic, M. Brezocnik and S. Buljan, 2016. Optimization of machining parameters for turning operation with multiple quality characteristics using Grey relational analysis. Tehnicki Vjesnik, 23: 377-382.
CrossRef  |  Direct Link  |  

Satheesh, J., T. Pasha, Harish and T. Madhusudhan, 2013. Optimal machining conditions for turning of AlSiC metal matrix composites using ANOVA. Intl. J. Innovative Res. Sci. Eng. Technol., 2: 6171-6176.
Direct Link  |  

Satishkumar, D., M. Kanthababu, V. Vajjiravelu, R. Anburaj and N.T. Sundarrajan et al., 2011. Investigation of wire electrical discharge machining characteristics of Al6063/SiC_p composites. Intl. J. Adv. Manuf. Technol., 56: 975-986.
CrossRef  |  Direct Link  |  

Shandilya, P., P.K. Jain and N.K. Jain, 2013. RSM and ANN modeling approaches for predicting average cutting speed during WEDM of SiC_p/6061 Al MMC. Procedia Eng., 64: 767-774.
CrossRef  |  Direct Link  |  

Shrivastava, S.M. and A.K. Sarathe, 2014. Influence of process parameters and electrode shape configuration on material removal rate, surface roughness and electrode wear in die sinking EDM. Intl. J. Emerging Technol. Adv. Eng., 4: 138-145.
Direct Link  |  

Singh, J. and V. Kumar, 2012. Investigation on the material removal mechanism and the thermal aspects in the electrical discharge machining process. Intl. J. Eng. Technol., 2: 1503-1507.
Direct Link  |  

Vishwakarma, M., V. Parashar and V.K. Khare, 2012. Advancement in electric discharge machining on metal matrix composite materials in recent: A review. Intl. J. Sci. Res. Publ., 2: 86-93.
Direct Link  |  

Yan, M.T. and H.T. Chien, 2007. Monitoring and control of the micro wire-EDM process. Intl. J. Mach. Tools Manuf., 47: 148-157.
Direct Link  |