References

Albuquerque, M.D.C.F.D. and J.D.A. Rodrigues, 2008. Study of the dimensions of double-torsion test specimens. Mater. Res., 11: 281-288.
Direct Link  |  

Bae, H., H. Diep and M. Ramulu, 2014. Influence of shot peening coverage on residual stresses induced in aluminum alloy 7050-T7 45. Proceedings of the 12th International Conference on Shot Peening ICSP, September 15-18, 2014, ICSP, Goslar, Germany, pp: 282-287.

Barthelat, F., K. Malukhin and H. Espinosa, 2002. Quasi-Static and Dynamic Torsion Testing of Ceramic Micro and Nano-structured Coatings using Speckle Photography. In: Recent Advances in Experimental Mechanics, Gdoutos, E.E. (Ed.). Springer, Dordrecht, Netherlands, ISBN:978-1-4020-0683-8, pp: 75-84.

Bhuvaraghan, B., S.M. Srinivasan and B. Maffeo, 2010. Optimization of the fatigue strength of materials due to shot peening: A survey. Intl. J. Struct. Changes Solids, 2: 33-63.
Direct Link  |  

Bidulska, J., T. Kvackaj, R. Bidulsky, M. Cabbibo and E. Evangelista, 2007. Effect of low strain rate on formability of Aluminium alloy. Metalurgija, 46: 157-159.
Direct Link  |  

Bressan, J.D., 2007. Plastic behavior and fracture of Aluminum and copper in torsion tests. AIP. Conf. Proc., 907: 521-526.
Direct Link  |  

Diani, J., C. Fredy, P. Gilormini, Y. Merckel and G. Regnier et al., 2011. A torsion test for the study of the large deformation recovery of shape memory polymers. Polym. Test., 30: 335-341.
CrossRef  |  Direct Link  |  

Dowling, N.E., 2013. Mechanical Behavior of Materials: Engineering Methods for Deformation, Fracture and Fatigue. 4th Edn., Pearson, London, UK., ISBN:9780131395060, Pages: 936.

Jonathan, A.S., R. Mitedin, E. Lara-Curzio and N.J. George, 2008. Fracture Toughness of Thin Plates by the Double-Torsion Test Method. In: Mechanical Properties and Performance of Engineering Ceramics II: Ceramic Engineering and Science Proceedings, Jonathan, A.S., R. Mitedin, E. Lara-Curzio and N.J. George (Eds.). John Wiley & Sons, Hoboken, New Jersey, USA., pp: 63-73.

Meng, Q. and G.S. Frankel, 2004. Effect of Cu content on corrosion behavior of 7xxx series aluminum alloys. J. Electrochem. Soc., 151: B271-B283.
CrossRef  |  Direct Link  |  

Mossakovsky, P.A., F.K. Antonov and L.A. Kostyreva, 2011. Investigation of failure criterion in dynamic torsion tests with solid cylindrical specimens. Proceedings of the 8th European International Conference on LS-DYNA Users, May 23-34, 2011, OECD, Strasbourg, France, pp: 1-6.

Nayak, S.Y., N.M. Amin, S.S. Heckadka, V. Shenoya and C S. Prakash et al., 2018. Design, fabrication and testing of carbon fiber reinforced epoxy drive shaft for all terrain vehicle using filament winding. Proceedings of the International Conferences on MATEC Web Vol. 153, February 26, 2018, EDP Sciences, Les Ulis, France, pp: 1-5.

Orduna, A. and P.B. Lourenco, 2005. Three-dimensional limit analysis of rigid blocks assemblages; Part I: Torsion failure on frictional interfaces and limit analysis formulation. Intl. J. Solids Struct., 42: 5140-5160.
Direct Link  |  

Patil, R.D. and P.N. Gore, 2013. Review the effect of specimen geometry on torsion test results. Intl. J. Innovative Res. Sci. Eng. Technol., 2: 7567-7574.
Direct Link  |  

Roesler, C.R.M., G.V. Salmoria, A.D.O. More, J.M. Vassoler and E.A. Fancello, 2014. Torsion test method for mechanical characterization of PLDLA 70/30 ACL interference screws. Polym. Test., 34: 34-41.
CrossRef  |  Direct Link  |  

Saborowski, E., M. Scholze, T. Lindner and T. Lampke, 2017. A numerical and experimental comparison of test methods for the shear strength in hybrid metal-thermoplastic-compounds. Proceedings of the IOP International Conference on Series: Materials Science and Engineering Vol. 181, March 16-17, 2017, IOP Publishing, Bristol, UK., pp: 1-13.

Schiltges, G., D. Gsell and J. Dual, 1998. Torsional tests on microstructures: Two methods to determine shear-moduli. Microsyst. Technol., 5: 22-29.
Direct Link  |  

Vainikka, O., J. Halinen, M. Pajula, A. Sarhaluoma and P. Kiviluoma et al., 2015. Implementation of a torsion testing device for 3D-printed plastic tubes. Proceedings of the 10th International Conference on DAAAM Baltic Industrial Engineering, May 12-13, 2015, Tallinn University of Technology, Tallinn, Estonia, pp: 205-210.