References

Bahrami, M., M.K.B. Givi, K. Dehghani and N. Parvin, 2014. On the role of pin geometry in microstructure and mechanical properties of AA7075/SiC nano-composite fabricated by friction stir welding technique. Mater. Des., 53: 519-527.
CrossRef  |  Direct Link  |  

Choi, E.Y., M.C. Kang, D.H. Kwon, D.W. Shin and K.H. Kim, 2007. Comparative studies on microstructure and mechanical properties of CrN, Cr-C-N and Cr-Mo-N coatings. J. Mater. Proc. Technol., 187: 566-570.
CrossRef  |  Direct Link  |  

Darwins, A.K., M. Satheesh and G. Ramanan, 2018. Experimental analysis of friction stir welding of dissimilar alloys AA7075 and Mg Ze42 using butt joint geometry. Intl. J. Mech. Prod. Eng. Res. Dev., 8: 505-512.
Direct Link  |  

Deepati, A.K., S. Tikaderb, H. Chaturvedi and P. Biswas, 2014. Experimental investigation of mechanical properties on friction stir welding of dissimilar aluminum alloys. Intl. J. Curr. Eng. Technol., 1: 242-246.
CrossRef  |  Direct Link  |  

Dinaharan, I., K. Kalaiselvan and N. Murugan, 2017. Influence of rice husk ash particles on microstructure and tensile behavior of AA6061 Aluminum matrix composites produced using friction stir processing. Compos. Commun., 3: 42-46.
CrossRef  |  Direct Link  |  

Dorbane, A., B. Mansoor, G. Ayoub, V.C. Shunmugasamy and A. Imad, 2016. Mechanical, microstructural and fracture properties of dissimilar welds produced by friction stir welding of AZ31B and Al6061. Mater. Sci. Eng. A., 651: 720-733.
CrossRef  |  Direct Link  |  

Gargatte, S., R.R. Upadhye, V.S. Dandagi, S.R. Desai and B.S. Waghamode, 2013. Preparation and characterization of Al-5083 alloy composites. J. Miner. Mater. Charact. Eng., 1: 8-14.
CrossRef  |  Direct Link  |  

Kadian, A.K. and P. Biswas, 2017. Effect of tool pin profile on the material flow characteristics of AA6061. J. Manuf. Proc., 26: 382-392.
CrossRef  |  Direct Link  |  

Kalaiselvan, K. and N. Murugan, 2013. Role of friction stir welding parameters on tensile strength of AA6061-B₄C composite joints. Trans. Nonferrous Met. Soc. China, 23: 616-624.
CrossRef  |  Direct Link  |  

Kant, G. and K.S. Sangwan, 2014. Prediction and optimization of machining parameters for minimizing power consumption and surface roughness in machining. J. Cleaner Prod., 83: 151-164.
CrossRef  |  Direct Link  |  

Lakshminarayanan, A.K. and V. Balasubramanian, 2008. Process parameters optimization for friction stir welding of RDE-40 aluminium alloy using Taguchi technique. Trans. Nonferrous Met. Soc. China, 18: 548-554.
CrossRef  |  Direct Link  |  

Li, Y., Q.I. Li, D. Li, W. Liu and G.G. Shu, 2016. Fabrication and characterization of stir casting AA6061-31% B₄C composite. Trans. Nonferrous Met. Soc. China, 26: 2304-2312.
CrossRef  |  Direct Link  |  

Orbulov, I.N., A. Nemeth and J. Dobranszky, 2008. XRD and EDS investigations of metal matrix composites and syntactic foams. Proceedings of the 13th European Conference on X-Ray Spectrometry, June 16-20, 2008, Cavtat, Croatia, pp: 1-8.

Rajakumar, S., C. Muralidharan and V. Balasubramanian, 2011. Influence of friction stir welding process and tool parameters on strength properties of AA7075-T₆ aluminium alloy joints. Mater. Des., 32: 535-549.
CrossRef  |  Direct Link  |  

Rajesh, G.L., V. Auradi and S.A. Kori, 2016. Mechanical behaviour and dry sliding wear properties of ceramic boron carbide particulate reinforced Al6061 matrix composites. Trans. Indian Ceramic Soc., 75: 112-119.
CrossRef  |  Direct Link  |  

Ramanan, G., J.E.R. Dhas and M. Ramachandran, 2017. Optimization of material removal rate and surface roughness for wire electric discharge machining of AA7075 composites using grey relational analysis. Intl. J. Veh. Struct. Syst., 9: 309-312.
CrossRef  |  Direct Link  |  

Ramanan, G., J.E.R. Dhas, M. Ramachandran and G.D. Samuel, 2017. Influence of activated carbon particles on microstructure and thermal analysis of AA7075 metal matrix composites. Rasayan J. Chem., 10: 375-384.
CrossRef  |  Direct Link  |  

Rani, M.G., V.S.P. Rao and K.R. Kotaiah, 2018. Prediction and optimization of machining parameters for cutting Al6061/MoS2 MMC material by WEDM process. J. Eng. Appl. Sci., 13: 8483-8488.
CrossRef  |  Direct Link  |  

Singh, S., 2012. Optimization of machining characteristics in electric discharge machining of 6061Al/Al₂O₃p/20P composites by grey relational analysis. Intl. J. Adv. Manuf. Technol., 63: 1191-1202.
CrossRef  |  Direct Link  |  

Sozhamannan, G.G., S.B. Prabu and V.S.K. Venkatagalapathy, 2012. Effect of processing paramters on metal matrix composites: Stir casting process. J. Surf. Eng. Mater. Adv. Technol., 2: 11-15.
CrossRef  |  Direct Link  |  

Trimble, D., J. Monaghan and G.E. O’Donnell, 2012. Force generation during friction stir welding of AA2024-T3. CIRP. Ann., 61: 9-12.
CrossRef  |  Direct Link  |  

Ugender, S., A. Kumar and A.S. Reddy, 2014. Microstructure and mechanical properties of AZ31B Magnesium alloy by friction stir welding. Proc. Mater. Sci., 6: 1600-1609.
CrossRef  |  Direct Link  |  

Zhang, L., S. Ji, G. Luan, C. Dong and L. Fu, 2011. Friction stir welding of Al alloy thin plate by rotational tool without pin. J. Mater. Sci. Technol., 27: 647-652.
CrossRef  |  Direct Link  |