References

Bahrami, M., K. Dehghani and M.K.B. Givi, 2014. A novel approach to develop aluminum matrix nano-composite employing friction stir welding technique. Mater. Des., 53: 217-225.
Direct Link  |  

Ceschini, L., I. Boromei, G. Minak, A. Morri and F. Tarterini, 2007. Effect of friction stir welding on microstructure, tensile and fatigue properties of the AA7005/10vol.% Al 2 O 3p composite. Compos. Sci. Technol., 67: 605-615.
Direct Link  |  

Dumpala, L. and D. Lokanadham, 2014. Low cost friction stir welding of aluminium nanocomposite-A review. Procedia Mater. Sci., 6: 1761-1769.
CrossRef  |  Direct Link  |  

Dwivedi, D.K., 2010. Adhesive wear behaviour of cast aluminium-silicon alloys: Overview. Mater. Des., 31: 2517-2531.
Direct Link  |  

Fernandez, G.J. and L.E. Murr, 2004. Characterization of tool wear and weld optimization in the friction-stir welding of cast aluminum 359+ 20% SiC metal-matrix composite. Mater. Charact., 52: 65-75.
Direct Link  |  

Fujimoto, M., S. Koga, N. Abe, Y.S. Sato and H. Kokawa, 2008. Microstructural analysis of stir zone of Al alloy produced by friction stir spot welding. Sci. Technol. Weld. Joining, 13: 663-670.

Kumar, B.A. and N. Murugan, 2014. Optimization of friction stir welding process parameters to maximize tensile strength of stir cast AA6061-T6/AlN p composite. Mater. Des., 57: 383-393.
Direct Link  |  

Lee, W.B., C.Y. Lee, M.K. Kim, J.I. Yoon and Y.J. Kim at al., 2006. Microstructures and wear property of friction stir welded AZ91 Mg/SiC particle reinforced composite. Compos. Sci. Technol., 66: 1513-1520.
Direct Link  |  

Liu, H.J., H. Fujii and K. Nogi, 2004. Microstructure and mechanical properties of friction stir welded joints of AC4A cast aluminium alloy. Mater. Sci. Technol., 20: 399-402.
Direct Link  |  

Maeda, M., H. Liu, H. Fujii and T. Shibayanagi, 2005. Temperature field in the vicinity of FSW-tool during friction stir welding of aluminium alloys. Weld. World, 49: 69-75.
CrossRef  |  Direct Link  |  

Masaki, K., Y.S. Sato, M. Maeda and H. Kokawa, 2008. Experimental simulation of recrystallized microstructure in friction stir welded Al alloy using a plane-strain compression test. Scripta Materialia, 58: 355-360.
Direct Link  |  

Mironov, S., Y. Zhang, Y.S. Sato and H. Kokawa, 2008. Crystallography of transformed β microstructure in friction stir welded Ti-6Al-4V alloy. Scr. Mater., 59: 511-514.
Direct Link  |  

Ohashi, R., M. Fujimoto, S. Mironov, Y.S. Sato and H. Kokawa, 2009. Effect of contamination on microstructure in friction stir spot welded DP590 steel. Sci. Technol. Weld. Joining, 14: 221-227.
Direct Link  |  

Park, S.H.C., Y.S. Sato, H. Kokawa, K. Okamoto and S. Hirano at al., 2009. Boride formation induced by pcBN tool wear in friction-stir-welded stainless steels. Metall. Mater. Trans. A, 40: 625-636.
CrossRef  |  Direct Link  |  

Prado, R.A., L.E. Murr, D.J. Shindo and K.F. Soto, 2001. Tool wear in the friction-stir welding of aluminum alloy 6061+ 20% Al 2 O 3: A preliminary study. Scr. Mater., 45: 75-80.

Prado, R.A., L.E. Murr, K.F. Soto and J.C. McClure, 2003. Self-optimization in tool wear for friction-stir welding of Al 6061+ 20% Al 2 O 3 MMC. Mater. Sci. Eng. A, 349: 156-165.
Direct Link  |  

RajKumar, V., M. VenkateshKannan, P. Sadeesh, N. Arivazhagan and K.D. Ramkumar, 2014. Studies on effect of tool design and welding parameters on the friction stir welding of dissimilar aluminium alloys AA 5052-AA 6061. Procedia Eng., 75: 93-97.
CrossRef  |  Direct Link  |  

Sato, Y.S., H. Kokawa, M. Enomoto and S. Jogan, 1999. Microstructural evolution of 6063 aluminum during friction- stir welding. Metall. Mater. Trans. A, 30: 2429-2437.
CrossRef  |  

Sato, Y.S., H. Yamanoi, H. Kokawa and T. Furuhara, 2007. Microstructural evolution of ultrahigh carbon steel during friction stir welding. Scr. Mater., 57: 557-560.
Direct Link  |  

Sato, Y.S., N. Harayama, H. Kokawa, H. Inoue and Y. Tadokoro at al., 2013. Evaluation of microstructure and properties in friction stir welded superaustenitic stainless steel. Sci. Technol. Weld. Joining, 14: 202-209.
Direct Link  |  

Suri, A., 2014. An improved FSW tool for joining commercial aluminum plates. Procedia Mater. Sci., 6: 1857-1864.
Direct Link  |  

Thomas, W.M. and E.D. Nicholas, 1997. Friction stir welding for the transportation industries. Mater Des., 18: 269-273.
Direct Link  |  

Wang, J., J. Su, R.S. Mishra, R. Xu and J.A. Baumann, 2014. Tool wear mechanisms in friction stir welding of Ti-6Al-4V alloy. Wear, 321: 25-32.
Direct Link  |  

Yasavol, N., A.A. Zadeh, M.T. Vieira and H.R. Jafarian, 2014. Microstructure evolution and texture development in a friction stir-processed AISI D2 tool steel. Appl. Surf. Sci., 293: 151-159.
Direct Link  |  

Zhang, Y., Y.S. Sato, H. Kokawa, S.H.C. Park and S. Hirano, 2008. Stir zone microstructure of commercial purity titanium friction stir welded using pcBN tool. Mater. Sci. Eng. A, 488: 25-30.
Direct Link  |